Patton electronic Network Card 1017 User Manual

USER  
MANUAL  
MODEL 1017 and  
1017S  
Mac Short Range  
Modem with  
Transformer Isolation  
SALES OFFICE  
(301) 975-1000  
TECHNICAL SUPPORT  
(301) 975-1007  
Part# 07M1017-A  
Doc# 082022UA  
Revised 3/25/94  
 
3.0 INSTALLATION  
RJ-11  
SIGNAL  
RJ-45  
SIGNAL  
The Model 1017 is easy to install. This section tells you how to  
properly connect the Model 1017 to the twisted pair interface and Mac  
phone port, and how to operate the Model 1017.  
1----------------GND†  
2----------------RCV-  
3----------------XMT+  
4----------------XMT-  
5----------------RCV+  
6----------------GND†  
1----------------N/C  
2----------------GND†  
3----------------RCV-  
4----------------XMT+  
5----------------XMT-  
6----------------RCV+  
7----------------GND†  
8----------------N/C  
3.1 CONNECTION TO THE TWISTED PAIR INTERFACE  
The Model 1017 supports data-only communication between a  
Mac and another Mac or another serial device. There are two require-  
ments for installation:  
When connecting two Model 1017s, it is necessary to use a  
“crossover” cable. The diagram below shows how a crossover cable  
should be constructed for an environment where both Model 1017s  
use a 4-wire R-11 connector. Similar logic should be followed when  
using an RJ-45 connector or a combination of the two.  
1. These units work in pairs. You must have one Model 1017 (or a  
compatible model) at each end of the two twisted pair cable.  
2. To function properly, the Model 1017's modular jacks must be con-  
nected to two twisted pairs of metallic wire. The pairs must be  
unconditioned, dry metallic wire, between 19 and 26 AWG (the  
higher number gauges may limit distance). Standard dial-up tele-  
phone circuits or leased circuits that run through signal equaliza-  
tion equipment are not acceptable.  
SIGNAL PIN# COLOR‡  
COLOR  
PIN# SIGNAL  
GND†  
RCV-  
XMT+  
XMT-  
RCV+  
GND†  
1
2
3
4
5
6
Blue --------------------White  
6
4
5
2
3
1
GND†  
XMT-  
RCV+  
RCV-  
XMT+  
GND†  
Yellow------------------Red  
Green ------------------Black  
Red---------------------Yellow  
Black -------------------Green  
White-------------------Blue  
For your convenience, the Model 1017 is available with two differ-  
ent twisted pair interfaces: an RJ-11 jack or an RJ-45 jack.  
3.1.1 TWISTED PAIR CONNECTION USING RJ-11 OR RJ-45  
Connection to ground is optional  
Standard color codes—yours may be different  
The Model 1017's RJ-11 and RJ-45 connectors on the twisted pair  
interface are pre-wired for a standard TELCO wiring environment (see  
Figure 1). The table on the following page describes the signal/pin  
relationships.  
3.2 CONNECTION TO THE MAC PHONE PORT  
The Model 1017 should be connected to your Mac through the  
1 foot extension cable. Simply plug one end of the cable into the  
Model 1017 and the other end directly into the phone (serial) port of  
your Mac. The pin-outs are listed below.  
1 - Blue  
1 - Blue  
2 - Orange  
2 - Yellow  
3 - Green  
4 - Red  
3 - Black  
4 - Red  
5 - Green  
6 - Yellow  
7 - Brown  
8 - Slate  
Serial Port Pinout (RJ-45)  
5 - Black  
6 - White  
1
2
3
4
5
6
7
8
=
=
=
=
=
=
=
=
N/C  
HSKi (Handshake In)  
HSKo (Handshake Out)  
Ground  
RD- (Receive Data-)  
TD- (Transmit Data-)  
N/C  
Figure 1. AT&T standard modular color codes  
N/C  
3
4
 
APPENDIX A  
Mini Din 8 to RJ-45 Cable  
Din 8 RJ-45  
SPECIFICATIONS  
Signal  
1---------------3 --------------HSKo (Handshake Out)  
2---------------2 --------------HSKi (Handshake In)  
3---------------6 --------------TD- (Transmit Data-)  
4---------------4 --------------Gnd (Ground)  
Transmission Format: Asynchronous  
Data Rate:  
300 to 19,200 bps  
5---------------5 --------------RD- (Receive Data-)  
6---------------4 --------------TD+(Transmit Data)  
7 -------------N/C-------------GPi  
Data Protection:  
High speed surge protection and  
transformer isolation (Model 1017S only)  
8 -------------N/C-------------RD+ (Receive Data)  
Distance:  
See table below  
Surge Protection:  
600W power dissipation at 1 mS and  
response time of 1.0 pS (Model 1017S only)  
TD+ is connected to ground  
Control Signal:  
The single Mac control line, Handshake In,  
turns on when the modem is connected  
3.3 OPERATING THE MODEL 1017  
Transmit Line:  
Transmit Mode:  
Transmit Level:  
Line Connection:  
Power Supply:  
4-wire, unconditioned line (2 twisted pairs)  
Once the Model 1017 is properly installed, it should operate trans-  
parently—as if it were a standard cable connection. Operating power  
is derived from the Mac's data and control signals; there is no  
“ON/OFF” switch.  
Full duplex  
0 dBm  
RJ-11, RJ-45  
No external power required, uses ultra low  
power from data and control signals  
Size:  
2.0” x 1.7” x 0.8”  
Distance Table (miles)  
Wire Gauge  
Data Rate  
19  
2.5  
5.5  
7.5  
8.5  
9.0  
24  
1.8  
3.7  
5.0  
5.6  
6.2  
26  
1.2  
2.5  
3.0  
3.7  
4.3  
19,200  
9,600  
4,800  
2,400  
1,200  
5
6
 
APPENDIX B  
BLOCK DIAGRAM  
7
 

Mountfield Lawn Mower EL 390R User Manual
MTD Blower 60 3857 0 User Manual
NETGEAR Modem CG814WG V3 User Manual
NETGEAR Network Router R6300 User Manual
Nortel Networks Telephone CallPilot Desktop Messaging User Manual
NuTone Door LA 203RWH User Manual
Panasonic CD Player CQ VX3300D User Manual
Panasonic Network Card 2SB0710A User Manual
Panasonic Telephone KXTG4744B User Manual
Partner Tech Tablet EM 200 WIN7;EM200XP User Manual