Patton electronic Network Router 07MSN5300 QS User Manual

SmartNode 5300  
Enterprise Session Border Router,  
IAD  
Quick Start Guide  
Important—This is a Class A device and is not intended nor approved for use in an  
industrial or residential environment.  
Sales Office: +1 (301) 975-1000  
Technical Support: +1 (301) 975-1007  
Part Number: 07MSN5300-QS, Rev. A  
Revised: May 21, 2014  
 
Always follow ESD prevention procedures when removing and replac-  
ing cards.  
Wear an ESD-preventive wrist strap, ensuring that it makes good skin  
contact. Connect the clip to an unpainted surface of the chassis frame  
to safely channel unwanted ESD voltages to ground.  
WARNING  
To properly guard against ESD damage and shocks, the wrist strap and  
cord must operate effectively. If no wrist strap is available, ground  
yourself by touching the metal part of the chassis.  
1.0 Power Up SmartNode  
1. Insert the barrel type connector end of the AC power cord into the external power supply connector.  
2. Insert the female end of the power cord into the internal power supply connector.  
3. Verify that the AC power cord included with your router is compatible with local standards. If it is not, con-  
tact Patton to replace it with a compatible power cord.  
4. Connect the male end of the power cord to an appropriate power outlet.  
5. Wait until the Power LED stops blinking and remains constantly lit. Now the SmartNode is ready to config-  
ure.  
2.0 Configuring the SmartNode  
Refer to the following manuals (available online at http://www.patton.com/kb/index.asp?dt=Manu-  
als%20(PDF) ) for detailed information about installing, configuring, operating, and troubleshooting  
the SmartNode:  
SmartNode 5300 User Manual: http://www.patton.com/manuals/SN5300-qs  
3.0 Connection via Console Access  
The SmartNode can be connected to a serial terminal over its serial console port, as depicted in figure 1.  
The interconnecting cables shall be acceptable for external use and shall be rated for the  
proper application with respect to voltage, current, anticipated temperature, flammability,  
and mechanical serviceability.  
CAUTION  
SmartNode 5300 Quick Start Guide  
3
 
Figure 1. Connecting SmartNode to Laptop via console access  
Configuration settings:  
19200 bps  
8 bits, no parity  
1 stop bit  
flow control off  
Note See section “Console Port” on page 35 for console port pin-outs.  
4
SmartNode 5300 Quick Start Guide  
 
A Customer and Technical Support  
Toll-Free VoIP support: call sip:[email protected] with a VoIP SIP phone  
Online support: www.patton.com  
E-mail support: [email protected]—answered within 1 business day  
Telephone support:  
Standard:1(301)975-1007(USA), Monday–Friday: 8:00 am to 5:00 pm EST(1300 to 2200 UTC/GMT)  
Alternate:+41(0)31 985 25 55 (Switzerland), Monday–Friday 9:00 am to 5:00 pm CET(08:00 to16:30 UTC/  
GMT)  
Fax: +1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)  
B Factory Defualt Settings  
Username: administrator  
The SmartNode is running as DHCP client and has at the same time a static IP address configured, on port Ether-  
net 0 /0:  
IP Address (Eth 0/0): DHCP  
Network Mask (Eth 0/0): n/a  
and  
IP Address (Eth 0/0): 192.168.200.10  
Network Mask (Eth 0/0): 255.255.255.0  
C Compliance  
C.1 EMC  
FCC Part 15, Class A  
EN55022, Class A  
EN55024  
EN50581  
C.2 Safety  
UL 60950-1/CSA C22.2 N0. 60950-1  
SmartNode 5300 Quick Start Guide  
5
 
IEC/EN60950-1 2nd Edition  
C.3 PSTN Regulatory  
This device is not intended nor approved for connection to the PSTN  
D Radio & TV Interference Statment (FCC Part  
15)  
This device generates and uses radio frequency energy, and if not installed and used properly-that is, in strict  
accordance with the manufacturer?s instructions-may cause interference to radio and television reception. The  
device has been tested and found to comply with the limits for a Class A computing device in accordance with  
specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection from  
such interference in a commercial installation. However, there is no guarantee that interference will not occur in  
a particular installation. If the device does cause interference to radio or television reception, which can be deter-  
mined by disconnecting the unit, the user is encouraged to try to correct the interference by one or more of the  
following measures: moving the computing equipment away from the receiver, re-orienting the receiving  
antenna and/or plugging the receiving equipment into a different AC outlet (such that the computing equipment  
and receiver are on different branches).  
E TEC Declaration of Conformity  
Patton Electronics, Inc declares that this device is in compliance with the essential requirements and other rele-  
vant provisions of Directive 2004/108/EC relating to electromagnetic compatibility, Directive 2006/95/EC  
relating to electrical equipment designed for use within certain voltage limits and Directive 2011/65/EC relating  
to RoHS compliance. The Declaration of Conformity may be obtained from Patton Electronics, Inc at www.pat-  
ton.com/certifications.  
The safety advises in the documentation accompanying the products shall be obeyed. The conformity to the  
above directive is indicated by the CE sign on the device.  
F Authorized European Representative  
D R M Green  
European Compliance Services Limited.  
Greyfriars Court  
Paradise Square  
Oxford, OX1 1BE, UK  
6
SmartNode 5300 Quick Start Guide  
 
F.1 Copyright statement  
Copyright © 2013, Patton Electronics Company. All rights reserved.  
The information in this document is subject to change without notice. Patton Electronics assumes no  
liability for errors that may appear in this document.  
F.2 Trademarks statement  
The term SmartNodeis a trademark of Patton Electronics Company. All other trademarks presented in this doc-  
ument are the property of their respective owners.  
F.3 Warranty, Trademark, & Compliance Information  
For warranty, trademark and compliance information, refer to the CopperLink User Manual located online  
SmartNode 5300 Quick Start Guide  
7
 
8
SmartNode 5300 Quick Start Guide  
 

Miele Cooktop KM 5773 User Manual
Miele Oven 09 593 460 User Manual
Mustang Survival Boating Equipment IC9001 U GD User Manual
Omron Scale bf306 User Manual
Oster Oven Small Digital Oven User Manual
P3 International Pest Control Equipment P7810 PIR User Manual
Panasonic Cell Phone EB X300 User Manual
Panasonic Network Card 2SD1821G User Manual
Panasonic Telephone Accessories KX TS560MX User Manual
Panasonic Telephone KXTG6591T User Manual